accordingly. If you want to stick the system into powersave mode - load the cpufreq_powersave.ko module
cpufreq # modprobe cpufreq_powersa... efine some decent defaults
#POWERMODE=performance
POWERMODE=powersave
SPEED=
[ -f /etc/sysconfig/cpufreq ] && sour... how we were called.
case "$1" in
start|low|lo)
POWERMODE=powersave
echo -n "Loading modules: ";
modprobe longh... cpu/cpu0/cpufreq/scaling_cur_freq`
echo "Actual powerstatus: ${DRIVER}($POWERMODE) @ ${SPEED}KHz"
else
echo "CPU Frequency S
me. If you don't want to be annoyed by short
# powerfailures, make sure that apccontrol powerout does nothing
# i.e. comment out the wall.
ON... use the initation of a shutdown.
#
# If during a power failure, the remaining battery percentage
# (as r... a system shutdown.
BATTERYLEVEL 5
# If during a power failure, the remaining runtime in minutes
# (as c... tiate a system shutdown.
MINUTES 3
# If during a power failure, the UPS has run on batteries for TIMEOUT
recovery recovery resets_all_to_default u need to power off unit. tbl_
3com OfficeConnect Wireless 11g C... recovery recovery resets_all_to_default u need to power off unit. tbl_
3com OfficeConnect Wireless 11g C... SV Network Management Card SNMP n/a TENmanUFactOryPOWER Admin nachzulesen unter http://www.heise.de/secur... Admin (none) Admin case sensitive username
Dell PowerConnect 2724 HTTP admin (none) Admin
Demarc Netw
exit
===== How this works =====
Pressing the power button runs a script called /etc/acpi/powerbtn.sh//
This script then calls the shutdown_dial... ver, some people are happy with editing /etc/acpi/powerbtn.sh to just say:
#!/bin/sh
/bin/kill -SI... owing lines after the # comments in the /etc/acpi/powerbtn.sh script.
<code>if ps -Af | grep '[s]hutdown_... /fastshutdown.sh
fi</code>
The first press of the power button will bring up the normal options, but a se
=== WARNING =====
The idle3 timer seems to be a power on only setting. That means that the drive needs to be powered OFF and then ON to use the new setting.
===== D
>
By default a switch toggles the corresponding power state (e.g., Switch1 controls Power1). Every time the switch gets flipped the power state of the relay toggles.
Damit zusammenhängen... <x> 15</code> you can decouple Switch<x> from its power output and it will instead send MQTT messages in ... duration to keep the corresponding Relay ON when Power<x> ON command is issued. After this amount of tim
m of the cabinet. The cube has a little wall-wart power supply that you can plug into the utility power outlet with the help of the adapter cord that com
B' 'GiB'</td><td>Unit conversion (<acronym title="powers of 10">SI</acronym> to <acronym title="powers of 2">IEC</acronym> prefixes)</td></tr>
<tr><t... >#</td><td class="nw">smartctl -A /dev/sda | grep Power_On_Hours</td><td>How long has this disk (system) been powered on in total</td></tr>
<tr><td>#</td><td class... class="nw"><a href="lkdb/mc.html">mc</a></td><td>Powerful file manager that can browse rpm, tar, ftp, ss
he lid!
===== Differing Behaviour Depending On Power Source =====
If you would like eeePC to **stay o...
If you'd rather just shut the screen off to save power use
<code bash>
#!/bin/sh
LID_STATE=`cat /proc/a... etc/acpi/lidbtn.sh
===== How to suspend with the power button =====
If you disabled suspend-on-close wi...
* Fn-F1 suspends the computer
* Pressing the power button will give you a menu with suspend as an op
