nismus des Via Epia ======
Via Epia unterstützt Powersave: kann Frequenz runterregeln. Bei Linux macht ... governors:
modprobe longhaul
modprobe cpufreq_powersave
Check using the dmesg command to see if it l... ry boot. For this - just add longhaul and cpufreq_powersave into the /etc/modprobe.preload file.
Using ... accordingly. If you want to stick the system into powersave mode - load the cpufreq_powersave.ko module
kernel: hiddev96: USB HID v1.10 Device [American Power Conversion Back-UPS CS 350 FW:807.q5.I USB FW:q5]... or "RFC" where APC is the powernet MIB,
# "APC_NOTRAP" is powernet with SNMP trap
# ca... #
# ======== Configuration parameters used during power failures ==========
#
# The ONBATTERYDELAY is th
recovery recovery resets_all_to_default u need to power off unit. tbl_
3com OfficeConnect Wireless 11g C... recovery recovery resets_all_to_default u need to power off unit. tbl_
3com OfficeConnect Wireless 11g C... Admin (none) Admin case sensitive username
Dell PowerConnect 2724 HTTP admin (none) Admin
Demarc Netw... latform All Multi public (none) Guest
EverFocus PowerPlex EDR1600 Multi admin admin Admin
EverFocus P
You can change the behaviour so that hitting the power button turns off the EEE without the dialog box. ... exit
===== How this works =====
Pressing the power button runs a script called /etc/acpi/powerbtn.sh//
This script then calls the shutdown_dialog file. In... ver, some people are happy with editing /etc/acpi/powerbtn.sh to just say:
#!/bin/sh
/bin/kill -SI
B' 'GiB'</td><td>Unit conversion (<acronym title="powers of 10">SI</acronym> to <acronym title="powers of 2">IEC</acronym> prefixes)</td></tr>
<tr><td>•</td><... >#</td><td class="nw">smartctl -A /dev/sda | grep Power_On_Hours</td><td>How long has this disk (system) been powered on in total</td></tr>
<tr><td>#</td><td class
>
By default a switch toggles the corresponding power state (e.g., Switch1 controls Power1). Every time the switch gets flipped the power state of the relay toggles.
Damit zusammenhängend:
Ein... <x> 15</code> you can decouple Switch<x> from its power output and it will instead send MQTT messages in
PDB Displays current status of the Power Driver Board
Usage:
pdb
P...
Remove the PRISM board, plug in a keyboard and power up the box. If you are lucky and the monitor "syn... the PRISM board/plug in PC monitor and keyboard
Power up (you will see the normal PC BIOS startup becau... m of the cabinet. The cube has a little wall-wart power supply that you can plug into the utility power o
he lid!
===== Differing Behaviour Depending On Power Source =====
If you would like eeePC to **stay o...
If you'd rather just shut the screen off to save power use
<code bash>
#!/bin/sh
LID_STATE=`cat /proc/a... etc/acpi/lidbtn.sh
===== How to suspend with the power button =====
If you disabled suspend-on-close wi...
* Fn-F1 suspends the computer
* Pressing the power button will give you a menu with suspend as an op
in/bf/bf.html|bogusforth]] - Obfuscated language, powerful, quite complete, unmaintained, based on forth,... ryone with an obfuscated syntax, and designing as powerful a language as possible with a tiny implementat... rogramming Language]] - Toy language. Harness the power of XML, by using it as a programming language. Co
To Hard Reset Samsung I9000 Galaxy S
- Turn the power off. If your Samsung Galaxy S is frozen, pull the... the Volume Down button
- Press and release the Power button
- You are now presented with a menu that... the Volume Down button
- Press and release the Power button
- Now simply confirm your decision: Volu
