n 0
}
Now let's create the script that will use functions in the file functions.sh. We can then use these functions. Notice the functions file is sou...
. /home/dave/bin/functions.sh
# now we can use the function(s)
echo -n "enter destination di... onments that are shared by a few backup scripts I use.
Here's the file.
$ pg backfunc
#!/bin/sh ... ODE}" ]; then
echo "Wrong code...exiting..will use defaults"
exit 1
fi
echo " The environment
e. This page contains all possible syntax you may use when editing the pages. Simply have a look at the... it this page". If you want to try something, just use the [[playground:playground|playground]] page. Th... nside the markers will not be formatted.
You can use <sub>subscript</sub> and <sup>superscript</sup>, too.
You can use <sub>subscript</sub> and <sup>superscript</sup>,
splay Manager. Before changing this line, you can use the telinit command to test prior to modifying the line. Use either telinit 3 to set to level 3, or telinit 5 ... /lib/X11/xdm/xdm-config as expected but I want to use kdm.
Let SuSE change those files! ;P
1. Of cou... configuring your initial ram disk image and then use
Etherboot to boot from diskette or EPROM, boot f... doesn't seem to be possible on the PCM-5820. Just use the part in SB16 emulation mode.
/etc/dhcpd.conf
s</code>
If you are confident in your ability to use the mount the command then you can use that, but you will have to manipulate the directo... d both your /home partition and / root partition. Use nautilus to mount your linux partitions. Then use these two commands so you can figure out if you h...
~ $ df -h
Filesystem Size Used Avail Use% Mounted on
aufs 1.6G 1.5G 103...
To run a command as administrator (user "root"), use "sudo <command>".
See "man sudo_root" for details
e Orinoco drivers are all kernel modules. You can use the modprobe command to load and unload modules or use the insmod and rmmod commands. See the man pages ... lspci command to take a look at the devices that use your PCI expansion bus. Here you can see that the... ild, but it is vital for subsequent attempts. You use the make mrproper command to do this; it must be ... his file lists all the kernel options you wish to use.
=== Backup Your Configuration ===
The .config
splay Manager. Before changing this line, you can use the telinit command to test prior to modifying the line. Use either telinit 3 to set to level 3, or telinit 5 ... /lib/X11/xdm/xdm-config as expected but I want to use kdm.
Let SuSE change those files! ;P
1. Of cours... configuring your initial ram disk image and then use
Etherboot to boot from diskette or EPROM, boot f... doesn't seem to be possible on the PCM-5820. Just use the part in SB16 emulation mode.
/etc/dhcpd.conf
infra-red light source is required if you wish to use your Wii remote to behave like a mouse from an IR... ui).
wmgui is an easy application that’s good to use for simple diagnostics on your wiimote, nunchuk a... use using acceleration data =====
If you want to use your Wii remote as a mouse by tilting your Wii re... [your wiimote's bluetooth address]
</code>
Please use your bluetooth device address for your Wii remote
t). If we run into some problems we might have to use airreplay to fiddle about.
I'll leave you to con... a crack, so lets start capturing packets. You can use kismet to capture files but I prefer airodump bec... e>
* interface is your wireless interface to use - required.
* output prefix is just the filna... s the specific channel we'll scan, leave blank or use 0 to channel hop.
* IVs flag is either 0 or 1
pe:
<code>wminput -c ir_ptr</code>
Now can use the use the Wii Remote the way you are used in the Wii me... part: Once extracted, navigate to /wmd-0.1.2/wmd. Use Gedit or Kwrite to edit Config.py.
Insert the a
/9</code>
To calculate the correct scaling size, use the expanded NTSC width of 854/2.35 = 368
2.35:1... /9</code>
To calculate the correct scaling size, use the expanded PAL width of 1024/2.35 = 432
==== 11... eg2video is usually used for DVD but you may also use mpeg1video for CIF resolutions.
* keyint: Used ... 9800 for DVD. For SVCD and DVD, you might wish to use lower values depending on your own personal prefe
er of the stream within this file that we want to use, also zero-based. "-map 0:3" therefore means that we want to use the fourth stream in the first (and only, in this... e the first "-map" option specifies the stream to use for the video and the second one specifies which stream to use for the audio:
<code>
$ ffmpeg -i mr.vob -map 0:... finishing now that I think of it). This is how we use solution 2:
<code>
$ ffmpeg -i oldmovie.vob -i a... ct 16:9 newmovie.mpg
</code>
Or, if you'd rather use MP2 audio and a lower audio bit rate:
<code>
$ f
being used by your file and the disk space being use by directory in the Linux system The du command can be use to find the size of file and the size of director... Linux system. The example below show the step to use the du command to get the size of file and the si... of current directory. ====
The du command can be use to determine the total size of file in current directory. The example below show the du command use with -s (summarize) and -h (human readable format
are extremely buggy for normal use and work only with
the 2.4 k... Kernel 2.4.20+ and CVS drivers use ethX for normal mode
and wif... Generally, Orinoco cards are not recommended for use with
Kismet due to these lim... GPL'd
rt2x00 drivers. Must use 1.2.2 beta 2 or newer drivers.
rt2500
for local rules) to allow anyone on the system to use uinput:
<code>KERNEL=="uinput", MODE="0666"</cod... the following line to allow anyone in <group> to use wminput, and adds only the desired users to <grou... xcellent tutorial at http://gentoo-wiki.com/HOWTO_Use_Multimedia_Keys can help you set this up. An ove... to a button in a wminput configuration file.
- Use wminput and the wiimote to generate that key symb
