be ich gefunden, das bei Nicht-Bewegung den Screensaver einschaltet. Kann ich umschreiben, damit es bei ... pberry Pi 2 rev. B using Raspbian with the xscreensaver
# installed. (if your screen lock does not work, install xscreensaver)
#
import os #for OS program calls
import sys #... _pin, io.IN)
print("Motion Activated (PIR) Screen Saver")
print("less than 30 seconds to leave the senso
s des Via Epia ======
Via Epia unterstützt Powersave: kann Frequenz runterregeln. Bei Linux macht das ... nors:
modprobe longhaul
modprobe cpufreq_powersave
Check using the dmesg command to see if it loade... ot. For this - just add longhaul and cpufreq_powersave into the /etc/modprobe.preload file.
Using long... dingly. If you want to stick the system into powersave mode - load the cpufreq_powersave.ko module
cpuf
and we tell it to write the face position and to save a drawing with the face detected:
<code>
mlpcascadescan andy.ppm -savepos -draw \
-model ~/temp/models/mlp-cascade19×19... ze n in pixel to recognize a face
* -nbest n : save the best n results only
* -dir <string> ... -> directory to store ouput files [.]
* -savepos -> save pos file
* -draw
sc = new oxField( 'shortdescription' );
$product->save();
</code>
Beispiel: Datensatz aktualisieren
<co... sc = new oxField( 'shortdescription' );
$product->save();
$product = oxNew( 'oxarticle' );
$product->se... sc = new oxField( 'shortdescription' );
$product->save();
</code>
====== Config ======
[[hhttp://wiki.... sc = new oxField( 'shortdescription' );
$product->save();
</code>
In this example the new record will be
<code>idle_start 400 60</code>
5.7.2 idle_screensaver
Selects the start time of the default screen saver. The screensaver is a slide show of the available snapshots.
<code>idle_screensaver START_TIMEOUT REPEAT_TIMEOUT
</code>
Options:
<c
unction: the current process working directory is saved, and it is restored after the execution is termi... t be set into raw mode using the stty command. We save the settings before dd is invoked and then restor... the function:
read_a_char()
# read_a_char
{
# save the settings
SAVEDSTTY=`stty -g`
# set terminal raw please
stty cbreak
# read and output only
lamp dump <lamp | blink | effect | mask>
lamp saver <on | off | on_time N | off_time N>
... ALS menu).
Press the DOWN ARROW key (move to the SAVE AND EXIT menu).
Press the DOWN ARROW key.
Press the DOWN ARROW key.
Press the ENTER key (SAVE AND EXIT).
Press the Y key (confirm).
Press the
Löschvorgang nur einmalig stattfindet.
=== LEMMI_SAVE_TIMER_PATH ===
Auszug aus der Datei '''/var/etc/lemmi-settings.txt''':
<pre>
#PARAMETER: LEMMI_SAVE_TIMER_PATH str
#
# Dieser Parameter wird ca. 30 S... ist '' (also keine Zeichen oder Optionen)
#
LEMMI_SAVE_TIMER_PATH =
</pre>
Beschreibt die Zeichenkette
/code>
Das muss man wohl auf "yes" setzen!
4. Save the file.
5. Run SuSEconfig. It will make the ch... d 16 Bit
(no acceleration, no zapp, diabled screensaver)
Acceleration muss ausgeschaltet sein!!!!
H-Freq
0).
<code>gsettings set org.gnome.desktop.screensaver lock-delay 0</code>
Erforderlich : Setzen Sie d... ildschirm aktiviert wird
<code>gsettings set org.gnome.desktop.screensaver lock-enabled true</code>
