all drivers except madwifi-ng:
airmon-ng stop <interface name>
For madwifi-ng, first stop ALL interfaces:
airmon-ng stop athX
Where X is 0, 1, 2 etc. Do a stop for each interface that iwconfig lists.
Then:
wlanconfig ath creat... rce expects the Win32/Cygwin
interface name. This should be used once the source
Other distros as well :D )
(B) ppp0 is internet interface (connected to Modem for example) and eth0 connect... # iptables --table nat --append POSTROUTING --out-interface ppp0 -j MASQUERADE
# iptables --append FORWARD --in-interface eth0 -j ACCEPT</code>
Step # 4 You are done! Te... nt 802.11g 802.11b any HTTP admin admin Admin Web interface is on 192.168.1.254 available on the LAN ports of
looking something like this:
<code> ./airodump <interface> <output prefix> [channel] [IVs flag]</code>
* interface is your wireless interface to use - required.
* output prefix is just the filname it'll prepend, - requi... cid.ivs". Assume WPA is on channel 6 and wireless interface is ath0.
<code> ./airodump ath0 lucid 6</code>
ill be used as root.
#root_container=.
# Network interface(s) to bind to (e.g. eth0), comma delimited.
# Thi... s option can be specified more than once.
network_interface=eth0
# IPv4 address to listen on (e.g. 192.0.2.1... are added to those determined
# from the network_interface option above.
# This option can be specified more
e DHCP server, it is recommended to specify which interface(s) the DHCP server will use.
Edit /etc/sysconfig/dhcpd by adding the appropriate interface to the DHCPDARGS= line.
The entry in /etc/sysc... n Mandrake 10, beide Systeme haben 2 Ethernet
Interfaces, ich versuche das ganze mal in einer ASCII Grafi
low, the firewall is connected to the Internet on interface eth0 and to the home network on interface eth1. The firewall is also the default gateway for the home networ... al feature is that the NAT all takes place on one interface; that of the home network (eth1).
You will addi
= Einfache Methode ===
Hierfür die /etc/network/interfaces mit einem Editor [4] und Root-Rechten bearbeiten... rrekten Einstellungen starten
# "manual" wird das Interface ohne TCP/IP starten (dies wird durch die Bridge h... er wird das ganze mit einer statischen IP für das Interface erklärt.
# Die UP wird von beiden - dem verkabelt
guments:
Using the module:
Predefined options:
Interface functions:
Querying Options:
Arguments
The mod... /sets/unsets the interactive excution option.
Interface functions
mbfl_declare_option keyword default bri... d then exit.
Catching signals
MBFL provides an interface to the trap builtin that allows the execution of
e DHCP server, it is recommended to specify which interface(s) the DHCP server will use.
Edit ''/etc/sysconfig/dhcpd'' by adding the appropriate interface to the DHCPDARGS= line.
The entry in ''/etc/sys... n Mandrake 10, beide Systeme haben 2 Ethernet
Interfaces, ich versuche das ganze mal in einer ASCII Grafi
en
Beispiele:
<code>
# ifconfig hme0 dhcp status
Interface State Sent Recv Declined Flags
hme0 ... code>
<code>
# ifconfig hme0 inet6 dhcp status
Interface State Sent Recv Declined Flags
hme0
run mysqlsniffer, you need to specify the network interface that MySQL is listening on. For me, it’s eth0.
<c... s for the command:
Usage: mysqlsniffer [OPTIONS] INTERFACE
OPTIONS:
–port N Listen for MySQL on port numb
n ein Häkchen machen)
z.B. Debian in /etc/network/interfaces
ethtool kann man auch einfach als pre-down oder... up haben in meinem Fall nicht funktoniert) in die interfaces-Konfiguration einbauen:
auto eth0
iface eth0 in