gespeicherten Daten zu verschlüsseln.\\
Vor der Initialisierung kann die Partition mit Zufallswerten ü... n vorbereitet wurde muss sie nun über cryptsetup initialisiert werden. Praktischerweise gibt es ein kle... eder ausgehängt. Zur Sicherheit kann nun noch die initial ram disk neu gebaut werden:
<code>
update-initramfs -u
</code>
Das Passwort kann auch weiterhin als
er CIS Software als Einwahl "Compuserve II"
- als Initstring
Einstellungen / Erweitert / weitere Einst... Befehl fuer manuelle
Modemkonfiguration(*3)
Als Initstring folgende Zeile eintragen, inklusive Anfuehr... konfiguration(*3) zur Anwahl mit T-Mobile.
Als Initstring folgende Zeile eintragen, inklusive Anfuehr... manuelle Modemkonfiguration(*3) mit Vodafone.
Als Initstring folgende Zeile eintragen, inklusive Anfuehr
rnel with some additional code, and appending the initrd to the end of the kernel.
The kernels that are... hcpd.leases</code>
Restart dhcpd
<code>/etc/rc.d/init.d/dhcpd restart</code>
Check that dhcpd is runn... t
o Restart xinetd
[root@bigboy tmp]# /etc/init.d/xinetd restart
Stopping xinetd: [ OK ]
Starti... : /opt/kde3/share/config/kdm/kdmrc
Now edit /etc/inittab and change the following line:
<code>id:3:ini
s set up correctly, you'll have to let aticonfig "initialize" it:
<code>
$ sudo aticonfig --initial -f
</code>
After this you should be able to restart your... l not need to do this.
Run
<code>sudo aticonfig --initial -f</code>
Now you'll likely have to edit your... o acquire AGP, error -1023
:(EE) fglrx(0): cannot init AGP
:(EE) fglrx(0): atiddxDriScreenInit failed, G
hcpd.leases</code>
Restart dhcpd
<code>/etc/rc.d/init.d/dhcpd restart</code>
Check that dhcpd is runn... t
o Restart xinetd
[root@bigboy tmp]# /etc/init.d/xinetd restart
Stopping xinetd: [ OK ]
Starti... : /opt/kde3/share/config/kdm/kdmrc
Now edit /etc/inittab and change the following line:
<code>id:3:initdefault:
to:
id:5:initdefault:</code>
In Slackware,
'' (''universe'', [3])
=== Nur Edgy: /usr/share/initramfs-tools/hooks/cryptroot editieren ===
Benutzt ... mehr Arbeit erforderlich. Die Datei '''/usr/share/initramfs-tools/hooks/cryptroot''' auf dem Festplatten... ules to load"
# exit 1
fi
</code>
=== /etc/initramfs-tools/modules editieren ===
Als nächstes wird die Datei '''/etc/initramfs-tools/modules''' mit einem Editor geöffnet u
PORT 3551</code>
Wenn alles konfiguriert: ''/etc/init.d/apcupsd start''
(Wenn man vorher start, (mit s... nction, so
# the first that occurs will cause the initation of a shutdown.
#
# If during a power failur... is below or equal to BATTERYLEVEL,
# apcupsd will initiate a system shutdown.
BATTERYLEVEL 5
# If durin... PS) is below or equal to MINUTES,
# apcupsd, will initiate a system shutdown.
MINUTES 3
# If during a p
ooth: L2CAP ver 2.7 Bluetooth: L2CAP socket layer initialized Bluetooth: RFCOMM ver 1.5 Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM TTY layer initialized usb 1-1.2: new full speed USB device using ohci_hcd and ... x: Permission denied kommen, dann hilft sudo /etc/init.d bluez-utils restart
In einem zweiten Terminal
forward = 1
Step # 2 Restart network
<code># /etc/init.d/network restart</code>
OR
<code> # service netw... om superstack II 1100/3300 Console 3comcso RIP000 initialize resets all pws to defaults
3com NetBuilder...
Lucent System 75 inads inads
Lucent System 75 initinitpw
Lucent System 75 locate locatepw
Lucent System 75 maint maintpw
Lucent System 75 maint rwm
in /etc/rc0.d erzeugt der auf das Skript in /etc/init.d/wake_on_lan zeigt. (Erst das Skript erzeugen!)
<code>cd /etc/rc0.d
ln -s /etc/init.d/wake_on_lan S80wake_on_lan</code>
Und hier das Skript wake_on_lan. Er muß nach /etc/init.d gespeichert werden und ausführbar sein. Dies ge... wol g
echo
;;
*)
# N=/etc/init.d/hwtools
# echo "Usage: $N {start|stop|res
# Using if [ ... ]
# If a string has not been initialized, it has no defined value.
# This state is ... $string1 ] # string1 has not been declared or initialized.
then
echo "String \"string1\" is not nu... # Shows $string1 as not null, although it was not initialized.
echo
# Let's try it again.
if [ -n "$s... s, the empty "$string1" and "]"
echo
string1=initialized
if [ $string1 ] # Again, $string1 s